3D Printing, Resin Casting & More

Commercial grade 3D Printing, Production Castings from 25 – 2,500 units.

Contact Us

3D Printing, Resin Casting

Angel Knight

Kabuki Studio Printing

Need specialist ultra detail 3D prints from people with over 7 years miniature 3D printing experience?
At low prices with a quick turnaround from our range of in house 3D printers?
If so, keep reading.


3D Prints and Casts for Ludus Magnus Studio

At Zealot, we have a suite of DLP resin 3D Printers. DLP prototyping produces tough resin master prototypes at an affordable price. With layers down to 1 micron Z steps, we can provide prints for any application. We set up support structures by hand so that your part has the minimum amount of supports to be cleaned up. Combined with the supports contact point being typically 100 microns or below, your model is produced at the highest quality. XY accuracy down to +/-13um (micron) yields sharp and smooth prints in all axis. We print in a range of materials, from off the shelf Envisiontec RC90 or heat resistant FusionGrey for vulcanised rubber moulds, even custom in-house blended resins. We will always recommend and print in the best material for your application.

DOD Wax printing produces models in a fragile, yet equally detailed material to DLP resin prints. For applications where physical supports would be impossible and a model could not be printed with DLP printers; we would then recommend printing in wax. This is because DOD printing uses a melt away support material that allows complex geometries to be printed with no intrusion from support rods. DOD wax produces parts down to 6 micron Z layers. The liquid piezo crystal deposition delivers an XY DPI 8,000 x 5,000 DPI. VoodooWorxJaw1 (Voodoworx Miniatures Printing) We would recommend our DOD printing for only specific models which require the support material. Since the costs of printing and the speed of printing are prohibitive. DOD wax printing is a slow process with a standard 28mm model taking upwards of 40 hours to prototype. Fragile thin parts like weapons, spears, antenna may not be suitable for DOD wax printing. TrollPrint1 (Trolls Outpost) Price: High Quality: High Leadtime: Slow
We also offer FDM printing for larger applications, test fitting, or for printing an armature of a model that can be traditionally sculpted over. BaseFDMeg1 (Base “Armature” for traditional sculpting over. Mitches Military Models) FDM extrudes molten plastic and can produce resolutions down to 50 um (micron) Z layers. With a nozzle diameter of 400 um (microns). While layers are clearly visible on models and fine detail is lost. FDM prints are cheap and fast which make them perfect for certain applications. IMG_1382 (Wall mounted gargoyle head. Zealot Miniatures) Price: Very Low Quality: Low Leadtime: Fast
We run a quality resin casting service to produce your range of miniatures in Polyurethane resin. Cast under both high vacuum and high pressure in a hybrid casting method, parts have superb detail and far less gates and sprues than other resin casting methods.

Prints and Castings for 4Grounds, Legends of the Fables Realms

We aim to produce casts that cater for collectors and painters who are looking for quality miniatures that will stand out against the competition. As well as by working with our established partners such as MDC (http://www.modeldesignconstruction.co.uk/ ) we can offer larger volumes of miniatures.

Prints and Castings for Grimlord Games

We have over six years of experience in digital sculpting specifically for miniature production. Producing sculpts 100% suitable for production. We take on in-house design and sculpting projects or we can bring in sculpting services, both digital and putty, from our established network of freelancers.

Example Pricing

For each stage of miniature production, typical prices are as follows:

Sculpting of a character model at 30mm scale – £300 – £600 depending on detail and which artist you use. It takes an artist around a week or more of work to create your character.

3D Printing Prototype of a character model at 30mm scale- £70-£80 with DLP which is what we usually suggest using for high resolution and smooth surfaces. Discounts available if multiple models are printed at once.

Master Mouldmaking of a character model at 30mm scale – £20. Discounts available if multiple models are moulded at once.

Production Mouldmaking of a character model at 30mm scale – £25.

Production Castings of a character model at 30mm scale – £2 – £2.50 depending on volume and complexity.

+VAT if applicable to your location and postage.


  • Fully booked for sculpting for the next 6 months. We can pass you onto a trusted freelancer who can handle your job.
  • Available for 3D printing and Prototyping.
  • Partial availability for Production, depending on your dates and required lead times.

Get In Touch

13 + 15 =

More Info

Zealot Miniatures can help you with all stages of model production. Design, sculpting and more, you name it. For more information or a quote, please do CONTACT US.
Phone: +44 (0) 1258 920085
Business Hours: 8:30am – 5:00pm M-F
Address: Zealot Miniatures, Sunrise Business Park, Blandford Forum, DT11 8ST, UK